E-mail Subscription

Enter your email address:

Delivered by FeedBurner

Syndicate RSS
Welcome

Mission Statement 

The purpose of FLAPS-2-APPROACH is two-fold:  To document the construction of a Boeing 737 flight simulator, and to act as a platform to share aviation-related articles pertaining to the Boeing 737; thereby, providing a source of inspiration and reference to like-minded individuals.

I am not a professional journalist.  Writing for a cross section of readers from differing cultures and languages with varying degrees of technical ability, can at times be challenging. I hope there are not too many spelling and grammatical mistakes.

 

Note:   I have NO affiliation with ANY manufacturer or reseller.  All reviews and content are 'frank and fearless' - I tell it as I see it.  Do not complain if you do not like what you read.

I use the words 'modules & panels' and 'CDU & FMC' interchangeably.  The definition of the acronym 'OEM' is Original Equipment Manufacturer (aka real aicraft part).

 

All funds are used to offset the cost of server and website hosting (Thank You...)

No advertising on this website - EVER!

 

Find more about Weather in Hobart, AU
Click for weather forecast

 

 

 

 

  FEEDBACK:  

If you see any errors or omissions, please contact me to correct the information. 

Journal Archive (Newest First)
« Full-time Construction - Light at the end of the Tunnel | Main | Freight Dispatched - Throttle Quadrant Australia Bound »
Friday
Aug162013

Wiring the Simulator - Aviation Wire

When I first began to work on my simulator, I used whatever wire was available; usually this was automotive electrical wire.  The wire was inexpensive and seemed to do the job; however, there were several shortcomings.  

To carry the appropriate amperage the wire selected was quite large in thickness; therefore, quite inflexible.  This inflexibility resulted in the wire coming loose at connections quite easily.  The thickness also made routing numerous wires quite challenging and at one stage, my simulator looked like a rat’s nest of snaking coloured wires.

After a few connection issues, I began to rethink my approach.  

I have since replaced the automotive wiring with a wire grade more suitable for the purpose.  The wire I use is aviation wire which is available in various gauges (thicknesses) and colour options.  The benefits in using this wire are it:

  • Withstands physical abuse during and after installation 
  • Has a good high and low temperature properties  
  • Is very flexible and small enough to be run in tight places
  • Can be obtained in varying gauges and colours
  • Has a high flex life  
  • Has good out-gassing characteristics
  • Has a fair cold flow property (probably not that important as the simulator is not going to altitude)

The wire can easily be obtained in rolls from supply chain stores or from e-bay.  Enter the following wire reference code into either e-bay or google:  Part Number: 22759-16-22-9; 22 AWG WHITE TEFZEL WIRE.

Please note, this is the wire I use (and many other builders).  There is a wide variety of wire available in the market that is suitable for building, so don't become overly concerned if you've already used a different type of wire.  The main point to remember is that wire is rated to the application and voltages your intending to use.  The wire mentioned is ideal for all wiring requirements of the simulator with the exception of very high voltage requirements.  High voltage requires a wire of lower gauge (thicker wire) to ensure minimal voltage drop over distance. 

The same type of wire as mentioned above can be purchased in differing gauges (thicknesses).  I find 22 gauge is a good overall gauge to use.  Remember that voltage (amps) is rarely being applied to the wire continuously (exception is from power supplies).

Easy Connect/Disconnect Connectors

Often there is a need to connect a piece of wire to another piece of wire or part and have the ability to be able to disconnect the wires easily and quickly.  For example, often panels must be removed from the center pedestal; having the ability to disconnect wires easily allows complete removal of the item without destroying the attachment wires!

There are dozens of connectors available for joining or extending wires – some are better than others.

I use (where possible and when voltage/amp requirements dictate) JR servo wire security clips.  These little clips allow three wires to enter to either side of the connection, are made from heavy duty plastic, and have a guaranteed clipping mechanism that will not unplug itself.  Search the Internet for JR extension servo clips. 

For applications requiring more than three wires, or higher voltage/amps, I use a high quality terminal block, Canon style plug or a D-Sub plug.  The later two requiring each wire to be very carefully soldered into the appropriate wire reciprocal in the plug.  I also use Mylar quick release plugs for some applications.

All other wires that require a permanent connection are usually soldered together with wire shrink wrap.  Soldering always provides the best connection.

PrintView Printer Friendly Version

EmailEmail Article to Friend

Reader Comments

There are no comments for this journal entry. To create a new comment, use the form below.

PostPost a New Comment

Enter your information below to add a new comment.

My response is on my own website »
Author Email (optional):
Author URL (optional):
Post:
 
Some HTML allowed: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <code> <em> <i> <strike> <strong>